Tubidy MP3 & MP4

En popüler MP3 müziklerinizi ve MP4 videolarınızı ücretsiz indirin. Geniş bir multimedya içeriği seçkisini keşfedin ve sorunsuz indirmelerin tadını çıkarın.

TIP #057: If you are testing your prototype and something is wrong, do not ...

4:02 |

Yükleniyor...

Hızlı erişim için Tubidy'yi favorilerinize ekleyin.

İlgili Videolar

TIP #056: If you are soldering a BGA manually (e.g. by a hot air gun), watch when it settles down

2:59 |

TIP #075: Consider not using dot (“.”) in symbol description e.g. 2.2uH. Do it this way instead 2u2

2:39 |

TIP #050: Read Errata documents

5:51 |

TIP #070: You may want to use 1% resistors instead of 5% resistors

5:42 |

TIP #055: Use different footprint for resistors and capacitors, even they are same size (e.g. 0805)

4:21 |

TIP #047: Use chips with good software support

4:50 |

TIP #063: Consider to place analogue circuits in corners of your PCB

4:35 |

TIP #062: On the cover page, include status of the schematic

4:08 |

TIP #007: Set the right height of your table

2:30 |

Test Your Prototype — A Fluids Engineer’s Story

40:42 |

Don't mix CONSTRUCTION with USE | Code Walks 029

2:58 |

TIP #084: Place hot components on the top

3:04 |

TIP #054: Place reference point of a footprint for through hole components to pin 1

6:21 |

TIP #069: You can use an industrial hot air gun to replace (solder / desolder) components ...

2:13 |

TIP #039: Be careful how you order pins on your connectors

8:25 |

Tubidy MP3 & MP4

TIP #057: If you are testing your prototype and something is wrong, do not ...

Type

Size

İlgili Videolar

TIP #057: If you are testing your prototype and something is wrong, do not ...

TIP #005: Make small test circuit boards

TIP #017: For complex boards, always build minimum 3, but rather 5 prototypes

TIP #032: Always do testing in environmental chamber

TIP #071: Consider not using autorouter

TIP #056: If you are soldering a BGA manually (e.g. by a hot air gun), watch when it settles down

TIP #075: Consider not using dot (“.”) in symbol description e.g. 2.2uH. Do it this way instead 2u2

TIP #050: Read Errata documents

TIP #070: You may want to use 1% resistors instead of 5% resistors

TIP #055: Use different footprint for resistors and capacitors, even they are same size (e.g. 0805)

TIP #047: Use chips with good software support

TIP #063: Consider to place analogue circuits in corners of your PCB

TIP #062: On the cover page, include status of the schematic

TIP #007: Set the right height of your table

Test Your Prototype — A Fluids Engineer’s Story

Don't mix CONSTRUCTION with USE | Code Walks 029

TIP #084: Place hot components on the top

TIP #054: Place reference point of a footprint for through hole components to pin 1

TIP #069: You can use an industrial hot air gun to replace (solder / desolder) components ...

TIP #039: Be careful how you order pins on your connectors

Tubidy MP3 & MP4

TIP #057: If you are testing your prototype and something is wrong, do not ...

Type

Size

İlgili Videolar

TIP #057: If you are testing your prototype and something is wrong, do not ...

TIP #005: Make small test circuit boards

TIP #017: For complex boards, always build minimum 3, but rather 5 prototypes

TIP #032: Always do testing in environmental chamber

TIP #071: Consider not using autorouter

TIP #056: If you are soldering a BGA manually (e.g. by a hot air gun), watch when it settles down

TIP #075: Consider not using dot (“.”) in symbol description e.g. 2.2uH. Do it this way instead 2u2

TIP #050: Read Errata documents

TIP #070: You may want to use 1% resistors instead of 5% resistors

TIP #055: Use different footprint for resistors and capacitors, even they are same size (e.g. 0805)

TIP #047: Use chips with good software support

TIP #063: Consider to place analogue circuits in corners of your PCB

TIP #062: On the cover page, include status of the schematic

TIP #007: Set the right height of your table

Test Your Prototype — A Fluids Engineer’s Story

Don't mix CONSTRUCTION with USE | Code Walks 029

TIP #084: Place hot components on the top

TIP #054: Place reference point of a footprint for through hole components to pin 1

TIP #069: You can use an industrial hot air gun to replace (solder / desolder) components ...

TIP #039: Be careful how you order pins on your connectors

Favorilere Ekle